Detax Mollosil Plus Refill Cartridge - 1 x 50ml (02354)

* Full Starter Kit also available - See other listing.

Long‐term soft relining material for chair‐side use, A‐silicone based, cold curing, biocompatible.

Material is directly applied onto the denture base. Cures fully in the mouth in 5 minutes, without heating. Suitable for indirect technique.Apply material directly to the denture after investing, flask is closed and pressed together. The material is then bench‐cured.

Colour: Gingiva

Intended Use
Definitive direct relining of dental prostheses

Indication
Suitable for all PMMA-based plastic materials.
Production of permanently soft relinings directly at the chairside or indirectly in the laboratory.
Removal of pressure points in the mandibular and maxillary areas.
For post-damming the A line in case of adhesion problems and flabby ridges.
As an elastic margin on maxillary dentures and for securing the position of the dentures by increased adhesion.
For elastic covering of sharp-ridged alveolar processes.
For covering implant areas and as overdentures.

Intended Users
Dentist, dental technician

1. Preparation of the denture
Removal of the old relining (Fig. 1) In general, an existing relining must be removed completely. Grind off the base to be relined by approx. 1 - 2 mm,
depending on the situation; at the vestibular, lingual or dorsal edges, incorporate a shoulder approx. 2 - 3 mm in height with a step of at least 1 mm; round
off the borders of the denture and clean the denture thoroughly.
Degreasing (Fig.2) Degrease with pure, medical alcohol and allow to dry.
 

Application of the mollosil® plus primer or mollosil® adhesive for adhesion (Fig. 3): All surfaces ground and to be relined to which the material is required
to adhere must be evenly and completely covered with mollosil® plus primer or mollosil® adhesive. Let mollosil® plus primer mollosil® Adhesive dry for
approx. 1 minute. Close the bottle immediately after use. Saliva, moisture or monomer liquids prevent adhesion of mollosil® plus or mollosil® to the denture.

2. Mixing
mollosil® plus: Application of the mixing jet / dispenser
Insert the cartridge according to special instructions (separately available, Automix1 REF 02343, Automix2 REF 02699). Remove and discard cartridge closure;
do not reuse! Slightly squeeze material until it flows evenly out of both openings. Mount the mixing cannula on the cartridge and squeeze out the required
material. Leave the mixing cannula on the cartridge as a closure after each use.


3. Direct chairside relining
Coating of the denture (Fig. 4): Prepare the denture as described under item 1. Apply mollosil®plus cartridge material by means of a dispenser (see item 2) or
mollosil® with the spatula (see item 2), taking care to avoid bubbles, to the vestibular, lingual or dorsal borders, respectively, covering the entire surface evenly.
Then coat the remaining prosthetic base plate completely (layer thickness: min. 2 mm). All denture areas that come into contact with the gingiva must be coated.Perform the functional movements (Fig. 5): Then place the denture in the patient’s mouth. Let him/her close the mouth in normal occlusion. The curing
process is completed after approx. 5 minutes. Then remove the relined denture from the mouth, and trim and paint it as described in item 5.

4. Indirect method in the laboratory
Invest the denture to be relined into a flask with counter. For easier removal of the denture, cover the teeth with silicone before pouring the counter, e.g. with
Flexistone® Plus. Remove the denture from the flask and then prepare it as described in item 1. Coat the model with a standard plaster-plastic insulation
(alginate). As described under item 3, apply mixed mollosil®plus or mollosil®, respectively, taking care to avoid bubbles, evenly over the entire surface of
the denture area to be relined (layer thickness: approx. 1 mm more than previously milled away). Close the flask with the counter and leave it under a press
for approx. 30 min. with light pressure, or in a pressure pot at 40 - 45 °C / 104 - 113 °F in a water bath for 10 min. Then remove the denture from the flask
and trim and paint it as described in item 5.

5. Final trimming and painting
Smoothing of the borders: First remove coarse excess with a sharp scalpel or scissors (Fig. 6). Then use suitable rotating tools (e.g Molloplast® cutters, prepolishers
and grinding sleeves, from approx. 8,000 RPM) with light pressure to clean and smooth the cut borders (Fig. 7).
Polish (Fig. 8): mollosil® plus polish or Lustrol (for mollosil®) should be used only to smooth the ground functional borders. Open the aluminum seal with a
spatula and plug on pipettes. Pipette both liquids at a mixing ratio of 1:1 onto a mixing block, mix homogeneously with a spatula, and apply with a brush;
allow to dry for approx. 5 min. at room temperature.

6. Cleaning recommendation for the patient
Thoroughly brush and rinse the relined denture several times a day with a soft toothbrush and neutral soap under running water; cleaning bath: max. 10 min.

Technical specifications mollosil® plus

Product color base/catalyst:red-brown / white

Mixing time: not applicable (Automix system)

Open time*: approx. 1 min 30 sec.

Curing time*: approx. 6 min 30 sec.

Retention time in the mouth: approx. 5 min.

Final hardness: approx. 28 Shore A

* from start of mixing at 23 ± 2 °C / 73 ± 3 °F, 50 ± 5 %
of rel. humidity. Higher temperatures shorten, lower
temperatures extend the indicated times.

Includes:

1 x 50ml Cartridge REFILL Mollosil® plus